Problem router 821+ (verbindung ADSL)

Bojan123 · Beitrag von **Bojan123** » 07 Okt 2006, 11:51

821+ (Annex B)
Firmware version: 6.22.0007 / 18.09.2006

Bild

jeder mal wen versuht verbinden -sie bild

Jirka · Beitrag von **Jirka** » 08 Okt 2006, 11:50

Hallo Bojan123,

wenn Du kein Deutsch kannst, probier es vielleicht mal in Englisch. Es soll hier einige geben, die das auch gut verstehen.

Viele Grüße,
Jirka

Bojan123 · Beitrag von **Bojan123** » 14 Okt 2006, 11:37

Can anyone help me or try to explane why this is happening, or what do i need to do?
Thank you.

froeschi62 · Beitrag von **froeschi62** » 14 Okt 2006, 11:43

Hallo,

at first try to change to the new firmware 6.24.0012.

Dietmar

Bojan123 · Beitrag von **Bojan123** » 16 Okt 2006, 14:13

I've change to the new firmware 6.24.0012 and still got same problem.
More suggestions?

ittk · Beitrag von **ittk** » 16 Okt 2006, 14:26

Try to setup the DSL Linecode with a fix value. LANConfig-Interfaces-->WAN-->ADSL-Procotol choose G.DMT.

Reboot and see if the Internetconnection is handeled in time.

backslash · Beitrag von **backslash** » 16 Okt 2006, 14:34

Hi Bojan123

- are VCI and VPI configured correctly for your internet provider?
- does your provider use PPPoE or another protocol? is the correct one configured?

regards
backslash

Bojan123 · Beitrag von **Bojan123** » 16 Okt 2006, 16:52

Thank you for your answers.

- ittk: it's allready on G.DMT
- backslash: VCI & VPI are set to ZERO (0), encapsulation is LLC-WUX and protocol is PPPoE. Provider uses PPPoE.

My provider hotline is not available right now, i'll ask them tomorow.
If this doesn't work, what else should i try?

backslash · Beitrag von **backslash** » 16 Okt 2006, 16:58

Hi Bojan123

VCI & VPI are set to ZERO (0),

this could be the problem. nearly all providers in germany use the UR2 parameters, which are VPI = 1 and VCI = 32

My provider hotline is not available right now, i'll ask them tomorow.
If this doesn't work, what else should i try?

just ask your provider for the correct settings. if you don't know, where to configure these settings, just post the provider's answer here...

regards
backslash

Bojan123 · Beitrag von **Bojan123** » 16 Okt 2006, 17:10

I'm not in Germany, i'm in Bosnia & Herzegovina and my provider is HT::NET Mostar.

Beitrag von **LoUiS** » 16 Okt 2006, 18:54

Hi Bojan123,

i "googled" a bit around and found vpi 0 vci 32 or vpi 1 vci 32 for HT::NET, just give it a try.

Ciao
LoUiS

Bojan123 · Beitrag von **Bojan123** » 17 Okt 2006, 09:01

Finally... i call them and VPI is 8, VCI: 35.

So... anyone from bosnia who use this router... configure it with these settings.

Thank you all for your support.

Best regards, Bojan.